Comment Only

12/15/2020

Wall RI OK- no permit card on site.

Carried Forward

12/15/2020

contractor to provide: Energy code compliance documentation. Mark and label available fault current at panelboards. Provide for GFCI protection of receptacle outlets per 210.8 - kitchens in other than dwelling units- including 3 phase 100 amps or less and single phase 50 amps or less.

Carried Forward

02/18/2021

contractor to provide: Energy code compliance documentation. Mark and label available fault current at panelboards. Provide for GFCI protection of receptacle outlets per 210.8 - kitchens in other than dwelling units- including 3 phase 100 amps or less and single phase 50 amps or less.

Carried Forward

02/18/2021

site visit only- verify apprentice personal registration

Carried Forward

03/04/2021

contractor to provide: Energy code compliance documentation. Mark and label available fault current at panelboards. Provide for GFCI protection of receptacle outlets per 210.8 - kitchens in other than dwelling units- including 3 phase 100 amps or less and single phase 50 amps or less.

Comment Only

03/04/2021

site visit only- verify apprentice personal registration

Comment Only

03/04/2021

Progress inspection- verbal with contractor. Floors had been sealed so limited access.

Carried Forward

03/18/2021

Contractor to provide: Energy code compliance documentation. Mark and label available fault current at panelboards. Provide for GFCI protection of receptacle outlets per 210.8 - kitchens in other than dwelling units- including 3 phase 100 amps or less and single phase 50 amps or less. See email correspondence.

Carried Forward

03/18/2021

Progress inspection at site. Inspector provided contractor contact info for Xcel Energy. Per Xcel designer- customer is responsible for metering/meter socket installation and/or repair. See email dated 03/18/2021.

Carried Forward

03/31/2021

Contractor to provide: Energy code compliance documentation. Mark and label available fault current at panelboards. Provide for GFCI protection of receptacle outlets per 210.8 - kitchens in other than dwelling units- including 3 phase 100 amps or less and single phase 50 amps or less. See email correspondence.

Carried Forward

03/31/2021

Progress inspection at site. Inspector provided contractor contact info for Xcel Energy. Per Xcel designer- customer is responsible for metering/meter socket installation and/or repair. See email dated 03/18/2021.

Comment Only

03/31/2021

03/20/2021- site visit only

Carried Forward

07/19/2021

Remove sufficient ceiling tiles to perform above ceiling inspection. Provide full access to facilitate panelboard cover removal. Remove all storage in front of electrical equipment in main electrical room. Verify MC cable at dishwasher is approved by health inspector.

Carried Forward

07/19/2021

1. Verify available fault current at panelboards- document as required. Verify if series ratings apply. Document as required. Install labeling as required by code. 2. Install arc flash warning labels. 3. GFCI function not operational at all at bar area. 4. GFCI receptacle(s) located behind equipment are not considered as readily accessible. 5. Call for above ceiling rough-in inspections when tiles have been removed for visual checks. 6. Re-support wiring methods above bar area- wiring methods not permitted to be supported from sprinkler piping. 7. Rooftop- a. Reverse polarity at GFCI receptacle- must be type WR b. Protect field installed wiring conductors from disconnect means to the wiring compartment in HVAC equipment. c. Verify available fault current at HVAC equipment- must be less than or equal to the SCCR marked at nameplate- most of the equipment has nameplate values of 5 K SCCR. 8. Based on the issues above we did not complete the inspection- please call for re-inspection. 9. At final approval- provide energy code compliance documentation.

Outstanding

07/19/2021

Remove sufficient ceiling tiles to perform above ceiling inspection. Provide full access to facilitate panelboard cover removal. Remove all storage in front of electrical equipment in main electrical room. Verify MC cable at dishwasher is approved by health inspector.

Outstanding

07/19/2021

1. Verify available fault current at panelboards- document as required. Verify if series ratings apply. Document as required. Install labeling as required by code. 2. Install arc flash warning labels. 3. GFCI function not operational at all at bar area. 4. GFCI receptacle(s) located behind equipment are not considered as readily accessible. 5. Call for above ceiling rough-in inspections when tiles have been removed for visual checks. 6. Re-support wiring methods above bar area- wiring methods not permitted to be supported from sprinkler piping. 7. Rooftop- a. Reverse polarity at GFCI receptacle- must be type WR b. Protect field installed wiring conductors from disconnect means to the wiring compartment in HVAC equipment. c. Verify available fault current at HVAC equipment- must be less than or equal to the SCCR marked at nameplate- most of the equipment has nameplate values of 5 K SCCR. 8. Based on the issues above we did not complete the inspection- please call for re-inspection. 9. At final approval- provide energy code compliance documentation.

Outstanding

08/02/2021

Met electrician told him to schedule Tim for final

Comment Only

08/09/2021

Final- partial pass. Pending health department approval of MC cable at dishwasher. Inspector note: Owner/tenant has had LED lighting installed.- NOT APPROVED. Installation requires electrical permit and inspection. Based on limited access- installation lacks listing labels and Class 2 labeling. Spoke to GC about situation. No approval for use of the space until installations are removed or installed to code with electrical permit.

Comment Only

08/11/2021

Illegal LED lighting installed by "others" was removed. Final - OK.